JCM EasyTec Receiver Micro 2+ 31 DCS Plus 2 channel 12/24V

MODE OF OPERATION
When a code is received, the receiver checks whether it is stored. If this is the case, it activates the corresponding channel depending on which mode has been programmed.

RADIO CLONE MODE SINGLE CHANNEL

• The single-channel receiver (without additional channel cards) can be activated by a single-channel transmitter, also by 2/3/4 channels of a transmitter)

The switching pulse or bislab mode is activated by the microswitch.

• Switching pulse: This function is the most commonly used. The relay remains activated as long as the switch of the receiver is pressed.
• Bistable: The relay has the following function: When the receiver is pressed for the first time, the relay engages and remains in this position even if the receiver pushbutton is released. Pressing the receiver a second time switches the relay off. A third press engages it again and so on.

PROGRAMMING MANUAL PROGRAMMING:
When the red programming indicator light is switched on, a long acoustic signal is active. Then send the code you want to program by activating the transmitter or access control card you want to store. You will hear a short acoustic signal each time a code is saved. If 10 seconds have elapsed without programming or if the button on the back of any already stored transmitter is pressed, the receiver exits programming mode and automatically switches to function mode where it is ready for output. For programming via radio, the radio programming selector must first be set to position Y (depending on the model).

PROGRAMMING VIA RADIO ADDITIONAL TRANSMITTERS WITH A "MASTER TRANSMITTER"
It is necessary to have a transmitter already stored in this receiver.
Using a ballpoint pen or a paper clip, press the button on the back of the transmitter that you know has already been stored in this receiver (if there is more than one receiver in the vicinity, the programming mode will be activated in all those that recognize this transmitter). The receiver emits a long beep to indicate that programming mode has been entered. Then, to program a new transmitter, you must activate the desired channel in each of them. To confirm correct programming, wait for the short beep after each entry. If 10 seconds have elapsed without programming or if the button on the back of any transmitter already memorized is pressed, the receiver exits programming mode and automatically switches to function mode where it is ready for output.

PROGRAMMING VIA RADIO ADDITIONAL TRANSMITTER WITHOUT "MASTER TRANSMITTER" (PIN MODE) To be able to work in this way, it is necessary to have previously programmed a PIN. This PIN (4-digit number) is stored in the first hand-held transmitter or directly on the memory card using a MANAGER+DCS or MINIMAN+DCS. To save this "PIN" in the receiver, press the programming button for 1 second until a 4-second beep is heard, which indicates a reset of the system, and activate the hand-held transmitter while holding the button down. The PIN is automatically stored in the receiver's memory when you hear a long beep. You will then hear two beeps to! indicate that the code storage phase has ended. From this point on, the receiver will recognize all! hand-held transmitters that have this PIN. Thus, the programming of an additional hand-held transmitter to which this PIN was previously entered is carried out by pressing the push-button on the back of [ the hand-held transmitter. A long beep is heard to confirm that the hand-held transmitter has been programmed.

PROGRAMMING WITH PORTABLE PROGRAMMING UNIT
Switch on the receiver. Pull out the memory card from the receiver. Insert it into the port provided on the portable programmer. Carry out the desired operations (saving reserve codes, copies, ... ) Insert the memory card back into the receiver.

DELETING THE MEMORY
A code cannot be deleted individually. The codes stored there can only be deleted by resetting the entire memory. To delete the codes stored in the receiver, 1 the programming button must be pressed for 5 seconds. The receiver emits a signal to indicate that it is in programming mode. After 5 seconds, you will hear intermittent acoustic signals indicating that the memory is empty and ready to receive new transmitters. The PIN of the P installation is retained if you are working in PIN-MODE. See further details in the instructions.

Technical data:

• Frequency 433 Mhz
• Screw-on antenna
• Code memory system self-learning or via programmer
• 31 codes / insertable 126 / 500 codes
• IP44
• Dimensions: 127 x 70 x 52 mm

Scope of delivery

• 1 x receiver
• 1 x antenna
• 1 x manual