Güde 8041-2 Expert Power Control 12x IEC C13, locking function, 2 sensor ports

The new IP power sockets effectively reduce the power consumption of the installation: collective switching off of
consumers, even in standby mode, as well as the integrated energy meters contribute to sustainable operation of the infrastructure.
In addition, the operator receives warning messages when leakage currents occur. This enables preventive maintenance measures before downtime occurs.
The PDUs have 4, 8, or 12 load outputs (IEC C13 or Schuko) on the back. This allows connected devices to be switched off and on in case of malfunction. This is also possible via media controllers and DCIM solutions. Defined threshold values also ensure that event-based switching operations can be initiated.
Two integrated sensor ports for optionally available sensors allow monitoring of ambient temperature, humidity, and air pressure. System-critical conditions are thus detected early. Thanks to hot-pluggable sensors, commissioning with the Expert Power Control series is completed quickly.

• Power ports individually switchable on the device, via HTTPS, SNMP, command line tool, and serial interface
• Switch state and switch-on delay (0...9999 seconds) configurable for each power port after power failure
• Power surges during simultaneous switching operations are prevented by an automatic latency time of 1 second
• Programmable schedules and on/off sequences
• 2 energy meters: one counts continuously, the other is resettable
• Measurement of current, voltage, phase angle, power factor, frequency, active, apparent, and reactive power
• Measurement of differential current type A
• Easily readable LED display for total current, IP address, sensor values, and error messages
• Each power port can be assigned its own watchdog (ICMP/TCP)
• Integrated surge protection (SPD) against damage to the device and consumers (L-N, L/N-PE)
• 2 ports for optional sensors for environmental monitoring (temperature, humidity, and air pressure)
• Load outputs can be switched when preset sensor threshold values are exceeded
• IEC lock connectors prevent accidental disconnection of cables

• Buzzer for acoustic alarm when sensor limit values are under/overrun
• Simple and flexible configuration via web browser, Windows or Linux program
• Firmware update possible during operation via Ethernet
• IPv6-ready
• HTTP/HTTPS, E-mail (SSL, STARTTLS), DHCP, Syslog
• SNMPv1, v2c, v3 (Get/Traps)
• TLS 1.0, 1.1, 1.2
• Radius and Modbus TCP protocol supported
• Configuration and control via Telnet
• Access protection via IP access control
• Controllable via iOS and Android app Gude Control
• Low power consumption
• Developed and manufactured in Germany
• Dynamic IP address assignment via DHCP or manual assignment of a fixed IP address
• Firmware update via Ethernet during operation (without restarting the device or outputs)
• SNMP Get/Traps (SNMPv1, SNMPv2c)
• Syslog support
• Access protection via IP access control
• Access protection via optional HTTP password
• Simple and flexible configuration via web browser, Windows or Linux program
• 10/100 Mbit/s

• Operating voltage: 230 V, max.: 16 A
• Input-side energy measurement
• Differential current measurement type A
• Integrated surge protection type 3 (SPD)
• 2 sensor ports with RJ45 socket
• HTTPS, SSL, IPv6, SNMPv3, Telnet, Radius, Modbus TCP

• Power connections IEC C20, max. 16 A, 230 V
• Load outputs: 8 IEC C13, max. 10 A with locking function
• Network connection RJ45 (10/100 Mbit/s)
• Serial interface RS232 (Sub-D 9-pin)
• 2 sensor inputs (RJ45) for optional sensors

• 19 inch, 1U
• LxHxD: 43.9 x 4.4 x 17.8 cm (without mounting brackets)
• Weight: approx. 2.2 kg
• Operating temperature: 0 - 50 °C
• Storage temperature: -20 - 70 °C
• Relative humidity: 0 - 95 % (non-condensing)